RESEARCH OF THE IMPACT ON PRODUCTIVITY OF PARAMETERS AND OPERATING MODES OF THE VIBRATION MACHINE DRIVE FOR CLEANING AND WASHING CONTAMINATIONS BY SUBMERGTD STREAM JET WITH SOLID PARTICLES
DOI:
https://doi.org/10.31618/ESSA.2782-1994.2021.1.68.13Keywords:
cleaning, washing of contaminants, vibration machine, dynamic parameters of the process and machine.Abstract
Analyzed the methods of cleaning and washing, the design of machines with a vibration drive. The choice of a specific method of cleaning and washing is determined depending on the type and properties of contaminants, on the requirements for the cleanliness of products, and the type of production. The scheme of operation of a vibrating machine for cleaning and washing machine parts in a pulsating flow of liquid with solid particles is considered and parameters that affect its performance are determined. The results of studies of physical phenomena during the formation of a pulsating submerged jet are presented, and the influence of design parameters and modes of the drive robots on the maximum jet pressure is determined. An analytical dependence of the maximum instantaneous pressure of the jet has been obtained experimentally, which makes it possible to determine the optimal ratios of parameters when designing a vibration machine for cleaning and washing contaminants.
References
Kozlov Yu. S., Kuznetsov O. K., Telnov N. F. Cleaning products in mechanical engineering. Moscow: Mechanical Engineering, 1982. 261 p.
Telnov N. F. Technology of cleaning of agricultural machinery. M .: Kolos, 1983. 256 p.
Numerical simulation of the process of jetdynamic washing of parts with blind holes. Tarasov V.A. and other. Bulletin of MSTU im. Bauman. Ser. "Mechanical Engineering". № 4. 2011. pp. 34-41.
Gromakovsky D.G., Burakov A.P., Kareva N.A. Development of low-frequency cavitation devices for washing the surface of machine parts and devices. Proceedings of the Samara Scientific Center of the Russian Academy of Sciences, №1(3). 2011. pp. 562-565.
Andilahai А. А. Abrasive treatment of parts with flooded jets. Mariupol: PGTU, 2006. 190 p.
A. s. 1130422 USSR, MKI3 at 08 V 3/10. Device for washing small articles. Hordeev А. I., Silin R. I., Syvchenko N. A. (USSR). №. 3613130; stated. April 15, 83; published 23.12.84, Bull. № 47.
Pat. on the utility model 116030 of Ukraine, IPC B03B 5/02. Vibrating machine for washing radio products. Hordeev A. I., Hordeev O. A., Migal V. G (Ukraine); in 2016 10059; Application. 03.10.2016; Publ.10.05.2017. Bull. № 9.
Staryi A. R., Hordeev A. I. Technology of cleaning and washing of contaminants of machine parts during repair by the flow of liquid with solid particles and a vibrating machine for its implementation. Herald of Khmelnytskyi National University. Technical Sciences. №4. 2019. pp. 7-14.
Hordeev A. I., Staryi A. R. Analysis of the process of interaction of the gas-liquid medium with the surface of the parts during washing before coating. Abstracts of the VI International Scientific and Technical Conference "Problems of durability of materials, coatings and structures." Vinnytsia, VNTU. 2018. pp. 14-15.
Pat. for utility model № 132837, IPC B08B 3/10 Vibrating machine for cleaning contaminants by the flow of solid particles and washing parts during equipment repair. Skiba M. E., Staryi A. R., Hordeev A. I., Hordeev O. A. U201810344; Application 19.10 2018. Publ. 03.11.2019 Bull. №5.
Staryi A. R., Hordeev A. I. Substantiation of parameters of dynamic processes of cleaning and washing in the vibrating machine by the immersed pulsating stream of liquid with firm particles. Herald of Khmelnytskyi National University. Technical Sciences. №6. 2020. pp.84-92.
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NoDerivatives 4.0 International License.
CC BY-ND
A work licensed in this way allows the following:
1. The freedom to use and perform the work: The licensee must be allowed to make any use, private or public, of the work.
2. The freedom to study the work and apply the information: The licensee must be allowed to examine the work and to use the knowledge gained from the work in any way. The license may not, for example, restrict "reverse engineering."
2. The freedom to redistribute copies: Copies may be sold, swapped or given away for free, in the same form as the original.
